Off-road Atlas LogoOff-road Atlas Logo
  • Behind The Wheel
  • How-To
  • News
  • Stories

How to Change the Air Filter on a Honda Pioneer 1000-5

By Megan Randall | How-To on February 10, 2020
2M READ
Share
0

Length: 3:02
Created: February 10, 2020

Transcript

Is it time to change your air filter on your Honda Pioneer? Today I’m going to show you how to do that. My name’s Kristen and this is Maintenance Matters.

You’re gonna start by removing your seat cushions. Fold in your seat belt latches and fold down the back seat.

Next you’re gonna raise your bed.

Next you’re gonna remove all the push pins from your access panel. Slide that out of the way.

Next you’re gonna loosen all of these bolts here. They’re gonna stay in there because they have these guides.

With all of these loosened, raise up your air filter lid. This has a seal inside of it. Make sure that’s in place and in good shape. If it’s not, you can get a new air filter kit from your dealership.

You’re gonna loosen this one more screw here. That’s to the surface.

Pull your air filter out. So this one’s obviously got some damage. Probably water got in there. You can smell fuel pretty strong, as well. We’re gonna go ahead and replace that one.

Next you’re gonna wipe out your air box. If you have access to compressed air you can use that as well. We’re just gonna use a clean rag. Get out any dirt, debris, any kind of leaves. You’ll also wanna brush out your air box lid. Check the seal again, make sure it’s all good. Let’s also wipe down the outside of it so when you’re reinstalling, no dirt falls back in.

Now you can install your new air filter. Make sure it seats correctly. Tighten this screw back down.

You can reinstall your air box lid. Tighten each one of these screws back down as well.

Now you can put this outer cover back on. Reinstall your push pins.

You can lower your bed back down and reinstall your seat cushions and you’re good to go. That’s how easy it is to change your air filter on a Honda Pioneer. Thanks for watching.

RELATED CONTENT: air filter6 Honda Pioneer18 machine maintenance53
Share
0

1 Comment

  1. Avatar for Kerry Kufner Kerry Kufner says:
    August 22, 2022 at 12:23 pm

    Yea please show how you keep the new gasket in place which they don’t. It is impossible

    Reply

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *



Related

  • How to Install a 4500 Lb. Black Ops Winch on a Polaris RZR

    How-To | 12 MIN READ
  • How to Install a 4" GDP Portal Gear Lift on a Polaris RZR PRO XP

    How-To | 13 MIN READ
  • How to Install a High Gear Kit and Clutch Kit on a Polaris RZR XP Turbo

    How-To | 18 MIN READ
  • How to Install a 4500 Lb. Black Ops Winch and Winch Mount on a Honda Talon

    How-To | 12 MIN READ
  • How to Install a Winch-Ready Bumper and Black Ops Winch on a Polaris Ranger XP 1000

    How-To | 12 MIN READ
  • How to Install a Heavy-Duty Carrier Bearing on a Polaris Ranger Crew

    How-To | 11 MIN READ
  • How to Install Aluminum Doors on a Can-Am Defender MAX

    How-To | 6 MIN READ
  • How to Install a 6" GDP Portal Gear Lift on a Can-Am Defender

    How-To | 17 MIN READ
  • How to Install a Heavy-Duty Radiator on a Polaris General

    How-To | 8 MIN READ
Copyright © 2021 SuperATV. All rights reserved.
SHOP NOW