Length: 7:15
Created: April 23, 2020
Hey everybody, today I’m going to show you how super quick and easy it is to install SuperATV’s rear windshield on this Can-Am Maverick X3.
First, lay it up against your machine before you take the film off to make sure it fits. We’ve already done this so now we can remove the protective film from both sides of our windshield.
This portion here with the long curvature is the top portion of the windshield. Grab the 90° seal and install it. Make sure the bulb portion of the seal is facing away. Start at the edge and apply it all the way across to the other side. Make sure it’s fully seated and then cut off the excess here.
[1:11] On the lower portion of the windshield, install the seal the same way. Run it all the way across to the opposite side and cut off the excess. Now this portion of the windshield is done and ready to be installed.
Grab the lower portion of the windshield and remove the film from it as well. Orient it just like this with the big curvature facing towards us. Take the straight seal and start right her and apply it all the way across this edge. Make sure it’s fully seated and cut off the excess.
Take the 90° bulb seal and install it just like this. Once it’s fully seated, cut off the excess. Now both portions of our windshield are ready to go.
[2:44] Now head over to this back panel on the machine. Grab it and pull it straight up and remove it. If you have a factory roof installed, untwist all of your fasteners for the roof, then just slide the roof down here onto the hood.
Next, grab the clamps. There are small and big clamps. For all the clamps down here we’re going to use the smaller clamps. This first clamp right here should be oriented just like this so that it comes together down here. Then put one right here. Make sure to leave them loose so you can adjust them. Install one right here and make sure that it comes together like this on the bottom.The last one goes right here so it comes together like this.
Now we’ll move on to the upper clamps. This firs one goes like this right here. The second one will be on the opposite side in the same location. And we’ll have one right here just like that, then one right here and one here.
[4:08] Grab the windshield and slide it into position. Grab two of the smaller and install sealing washers to each of them. Just make sure that the sealing portion is facing away from the head. Slide the screw in from the inside on this hole right here, making sure it’s lined up with the clamp. Get the nut started.
Then go to the other side in the same location and do the same thing. Get the hardware started through and get the nut started.
Next grab two of the larger allen headed screws, two sealing washers, and two nylock nuts. Get these started through the upper clamps here. We’ll have the bolt come in from the inside. You can use a screwdriver to help you line up the hole. Then do the same thing on the opposite side, and then for the side clamps.
[5:47] With the upper portion installed, grab the lower portion. From inside the machine here, get everything lined up and get it installed. Once we have all our hardware started as shown here, we’re going to go through and fully tighten our hardware. Now we’re going to reinstall all of the components that we previously removed and there you have it.
That’s how super easy it is to install SuperATV’s rear windshield on this Can- Am Maverick X3. For more information on this windshield or any of SuperATV’s great products, feel free to give us a call at 855-743-3427, or check us out online at SuperATV.com.
Thanks for watching and we’ll catch you next time.
4 Comments
Hey I bought this back windshield for my 2018 can am X3 4 seater and for the life of me I cannot get the upper and lower rubber brackets to connect. I am not sure if my cage bars are thicker then ordinary or what. Do you offer a bigger size of mounting brackets for the bottom or top. I was able to get the side brackets not problem. If you could point me in the right direction in where to get some; that would be greatly appreciated!
Thanks.
Hey Kyle! That rear windshield should fit all X3 models. The first thing I would recommend would be to check if the size listed on the brackets match what you got with the kit. You should have received (2) 1.75″ clamps and (2) 2.5″ clamps. If those measurements are correct, the next step would be to take a couple of pictures of it all to send into us and we’ll take a look so you get it on there just right. If those are incorrect, please take a picture of them and send them to us, so we can get the correct ones sent to you. You can send these pictures to sales@superatv.com with a brief explanation. You can also feel free to give us a call at 855-743-3427 if you prefer. Thanks for tuning in!
Got the back windshield ,front windshield and roof .the backwindshield for my 2020 canam XMR fits like a dog turd wish I knew before I bought it.
Hey John. I’m sorry to hear about that. Have you tried giving us a call? If you can tell us what the issues were specifically and have your order info ready, hopefully we can help you get this resolved. Thanks for the support!