Off-road Atlas LogoOff-road Atlas Logo
  • Behind The Wheel
  • How-To
  • News
  • Stories

How to Install a Seat Lowering Base on a Polaris RZR Turbo S

By Tyler Mingione | How-To on July 30, 2020
3M READ
Share
0

Length: 6:35
Created: July 30, 2020

Transcript

[0:00] Are you looking to lower your seats? SuperATV’s got you covered with our 2″ Seat Lowering Base and today we’re going to show you how to install one on this RZR Turbo S. Let’s get to it!

Remove the Seat

First, we’ll reach behind the seat and grab hold of the lever. Pick up on your seat and remove it from the machine, then we’ll flip our seat over and set it in a good location where we can work on it.

After that, take a T27 and remove the following screws. You just have to wiggle it off of this right here—off your spring. Take that and set it aside.

[0:57] Now we have our seat lowering base sitting here in front of us. We’re going to get our lock bracket, which will look just like this, and we’re also going to get our big Allen-headed hardware with one plastic washer.

Install the Lock Bracket

On the head side, we’ll get two of our M8 Nylocs and two more of our plastic washers. We’ll take our lock bracket and our big Allen-headed bolt with a shoulder on it. Slide it through one of our holes, take our plastic washer, and slide it on top. We’ll do the same thing over here for this hole.

Get our plastic washer on and slide them through this hole right here, as well as this hole here. We’ll get our hardware started and then tighten up our hardware. You don’t want to tighten these too tight—just to the point where there’s no up and down movement. As you can see, we still have movement for our lock bracket to work.

[2:38] Next we’re going to take our spring and install it to our lock bracket here as well as on the base. You may need a little screwdriver just to pull some tension and get it to slide on the base here.

Adjust the Seat Lowering Base

Make sure it functions well, which ours does, and then take the seat lowering base and grab hold of the adjuster here on the seat. Adjust it all the way forward to where our holes are in the back of the adjustment.

Then we’ll take one of our spacers and lay them down. We’ll take one of our screws and install the lock washer, then a flat washer. Go ahead and start all of the hardware.

[3:53] The way it should go is this: the lock washer, the washer, and the spacer. Once everything is started we will fully tighten all of our hardware.

Now that the hardware is tightened, we’ll make sure everything is still working well. Make sure our seat can adjust just like that.

[4:56] After that, we’ll grab our seal and apply it on the back side of the frame. Start here and run it all the way to the outside, right there, down to here. Then cut off the excess. Next we’ll run it to this bolt and cut that excess as well.

Re-Install the Seat

Finally, we’ll grab our seat and re-install it to the machine. Slide it into position and get the harness or seat belt pulled back out. Pull on it to make sure it’s in there correctly.

Now if you look at the passenger side from the driver’s side, you can tell a big difference between the two. Go ahead and hop in and get your seat adjusted to where you like it.

And there you have it! That’s how super quick and easy it is to install SuperATV’s 2″ Seat Lowering Base on this Polaris RZR Turbo S. For more information on these lowering bases or any of SuperATV’s great products, feel free to give us a call at 855-743-3427 or check us out online at SuperATV.com. Thanks for watching and we’ll catch you next time.

RELATED CONTENT: installation256 Polaris RZR Turbo S16
Share
0

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *



Related

  • How to Install High Clearance A-Arms on a Honda Talon 1000R

    How-To | 6 MIN READ
  • How to Install a 6" Lift Kit on a Honda Pioneer 1000

    How-To | 12 MIN READ
  • How to Install High Clearance Forward Offset A-Arms on the Polaris RZR PRO XP

    How-To | 9 MIN READ
  • How to Install a Plug & Play Turn Signal Kit on a Polaris General

    How-To | 8 MIN READ
  • How to Install Winch & Winch Mount on Polaris RZR 1000

    How-To | 10 MIN READ
  • How to Install a Plug & Play Turn Signal Kit on a Can-Am Defender

    How-To | 11 MIN READ
  • How to Install a Rev1 Clutch Kit on a Polaris RZR XP Turbo S

    How-To | 10 MIN READ
  • How to Install High Clearance Forward Offset A-Arms on a Honda Pioneer 1000-5

    How-To | 6 MIN READ
  • How to Install a Gen 3 GDP Portal Gear Lift on a Polaris RZR XP 1000

    How-To | 8 MIN READ
Copyright © 2021 SuperATV. All rights reserved.
SHOP NOW