Off-road Atlas LogoOff-road Atlas Logo
  • Behind The Wheel
  • How-To
  • News
  • Stories

How to Install a Kawasaki Teryx 4 Flip Up Windshield

By Tyler Mingione | How-To on November 1, 2018
2M READ
Share
0

Length: 3:25
Created: November 1, 2018

Transcript

Hey guys, Kristen here at SuperATV and today we’re going to install a Kawasaki Teryx 4 flip up windshield. Let’s get started.

Install the Bulb Seal and Catch

[00:16] We’re going to start by installing the bulb seal, and that is going to go on the lower portion of the lower windshield that comes in contact with your hood. Now, you will have to leave this film on for the most part just peel it back enough to get that seal on. To ease installation you may want to soak the bulb seal in hot water prior to installing. Now that you have the seal installed, you can cut off the excess.

Now, we’re going to install the catch and catch support with the provided hardware. Alright, now that we’ve got the bulb seal and catch installed, it is time to get this dude on.

Install the Lower Windshield, Gasket, and Handle

[01:05] Next, we’ll take this and secure it to our roll cage. As you are installing these, be sure not to get them too tight because if you have to adjust this you want to be able to move it. Okay we’ve got that installed so now it is time to put the gasket on. Cut the excess gasket.

Next, we’re going to install the handle and the handle support with the provided hardware. Make sure that this is on the inside of the windshield facing up towards the top portion.

Install the Upper Windshield, Gas Struts, and Finish Up

[02:00] Let’s get this upper windshield on. Now we get to install our gas struts. This is going to go on the pivot block into the center hole.

Alright guys, now we have everything installed, so we are going to close it and make sure your latch lines up with your catch. If so, then you’re good to tighten the rest of your hardware up.

Alright guys, so we’ve got this windshield installed and tightened up so it’s time to remove the protective film.

So that wraps up the installation of our Kawasaki Teryx 4 flip up windshield. And for more information on this and other great SuperATV products hop online at SuperATV.com or give us a call at (855)-743-3427.

Thanks for watching and happy riding.

RELATED CONTENT: flip windshields19 installation256 Kawasaki Teryx9 UTV windshields57
Share
0

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *



Related

  • How to Install a Rhino Driveline Prop Shaft on a Polaris RZR 1000

    How-To | 7 MIN READ
  • How to Install High Clearance Forward Offset A-Arms on the Polaris RZR PRO XP

    How-To | 9 MIN READ
  • How to Install a Rev1 Clutch Kit on a Polaris RZR XP Turbo S

    How-To | 10 MIN READ
  • How to Install a Plug & Play Turn Signal Kit on a Can-Am Defender

    How-To | 11 MIN READ
  • How to Install a Gen 3 GDP Portal Gear Lift on a Polaris RZR XP 1000

    How-To | 8 MIN READ
  • How to Install a Rear Windshield on a Textron Wildcat XX

    How-To | 3 MIN READ
  • How to Install Winch & Winch Mount on Polaris RZR 1000

    How-To | 10 MIN READ
  • How to Install a Plug & Play Turn Signal Kit on a Polaris General

    How-To | 8 MIN READ
  • How to Install a 6" Lift Kit on a Honda Pioneer 1000

    How-To | 12 MIN READ
Copyright © 2021 SuperATV. All rights reserved.
SHOP NOW