Off-road Atlas LogoOff-road Atlas Logo
  • Behind The Wheel
  • How-To
  • News
  • Stories

How to Install a Full Windshield on a Textron Wildcat XX

By Tyler Mingione | How-To on November 14, 2018
<1M READ
Share
1

Length: 2:53
Created: November 14, 2018

Transcript

Hey everybody, Braden here from SuperATV and today we are going to be installing our Textron Wildcat XX Full Windshield. So let’s get started.

Apply the Bulb Seal and Straps

[00:20] First thing we are going to do is install the bulb seal to the lower portion of the windshield which is the side with the contours that fit the hood. Before you install the bulb seal, be sure to peel back the protective film. Then, once you get through the contours be sure to firmly press on the bulb seal to ensure that it fully seals and once you get here go ahead and cut off the excess.

The next thing that we are going to do is install the heavy duty Velcro straps to the windshield, but when installing, be sure that the hard plastic portion is facing towards the outside of the machine.

Install the Windshield on Your Wildcat XX

[01:20] Now that the pre-installation is complete we can install the windshield on the machine. You will not need to remove the roof of your machine, you’ll just slide the windshield up underneath of it. Once the windshield is in place we are going to attach our heavy duty Velcro straps to the cage.

Now that the windshield is installed on the machine we are good to go to peel the protective film. So that is how super easy it is to install SuperATV’s full windshield on this Textron Wildcat XX.

For more information on this full windshield or any of SuperATV’s awesome products, give us a call at (855)-743-3427 or check us out online at SuperATV.com. Thanks for watching and have a great day.

RELATED CONTENT: full windshields9 installation262
Share
1

2 Comments

  1. Avatar for Jan Cowley Jan Cowley says:
    February 7, 2021 at 12:01 pm

    I have rearview mirrors attached to the sides of the cage. Is it OK for the windshield to sit on top of the mirror brackets?

    Reply
    • Avatar for Tyler Lichlyter Tyler Lichlyter says:
      February 9, 2021 at 10:01 am

      Hey Jan! Yep, the windshield is meant to sit on top of those brackets. The bulb seal will form around the clamp. Thanks for the support!

      Reply

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *



Related

  • How to Install a Rev1 Clutch Kit on a Polaris RZR XP Turbo S

    How-To | 10 MIN READ
  • How to Install High Clearance A-Arms on a Honda Talon 1000R

    How-To | 6 MIN READ
  • How to Install a Plug & Play Turn Signal Kit on a Polaris General

    How-To | 8 MIN READ
  • How to Install a Plug & Play Turn Signal Kit on a Can-Am Defender

    How-To | 11 MIN READ
  • How to Install a Gen 3 GDP Portal Gear Lift on a Polaris RZR XP 1000

    How-To | 8 MIN READ
  • How to Install Winch & Winch Mount on Polaris RZR 1000

    How-To | 10 MIN READ
  • How to Install a Rear Windshield on a Textron Wildcat XX

    How-To | 3 MIN READ
  • How to Install a 6" Lift Kit on a Honda Pioneer 1000

    How-To | 12 MIN READ
  • How to Install High Clearance Forward Offset A-Arms on the Polaris RZR PRO XP

    How-To | 9 MIN READ
Copyright © 2021 SuperATV. All rights reserved.
SHOP NOW