Off-road Atlas LogoOff-road Atlas Logo
  • Behind The Wheel
  • How-To
  • News
  • Stories

How to Install Nerf Bars on a Polaris RZR PRO XP

By Megan Randall | How-To on March 3, 2020
2M READ
Share
0

Length: 3:14
Created: March 3, 2020

Transcript

[0:00] Are you looking for more side protection on your RZR PRO XP? Well, SuperATV’s got you covered with our heavy-duty nerf bars. Today we’re gonna show you how to get them installed. So let’s get to it.

The first thing we’re gonna do is get our skid plate out of the way, or remove the center section.

We just went ahead and removed the entire center section of our skid plate. We’re gonna be upgrading anyway, so we figured there’s not a better time to go ahead and do it!

[0:26] Now we’re gonna grab two of our spacers, three of our M10 bolts, and three of our flat washers. We’re gonna get some Loctite as well.

We’ll go ahead and apply Loctite to our hardware. Now take a flat washer and throw it on the bolt as well. Take this bolt and slide it through the frame. When you slide it through, make sure you slide your washer all the way forward first.

Then we’ll take our spacer and slide it over the bolt, and then add more Loctite on it. We can put our spacer on this one first, and we’ll go ahead and take our nerf bar. Start to get it lined up. We’re gonna go ahead and get our center bolt started.

[1:28] We’ll just want to leave it started. We don’t want to fully tighten it yet.

We’ll move up here to the front. Next we’re gonna go inside our machine. We went ahead and removed our seat just so we can better illustrate where we’re gonna be doing this.

You’re gonna see this portion of the frame here rounded out. That’s where our bolt’s going to go through. We’ll go ahead and get our last bolt and apply some Loctite to the threads.

Take our bolt, stick it through, and line it up with our nerf bar. Then we’ll go ahead and completely tighten this one. Now go through and fully tighten the rest of them.

[2:33] We just want to make sure we get everything fully tightened. Then repeat the steps for the opposite side.

Now what you’re gonna do is go back through and double check all of your hardware.

That’s how super quick and easy it is to install SuperATV’s Heavy-Duty Nerf Bars on the RZR PRO XP. For more information on these nerf bars or any of SuperATV’s great products, feel free to give us a call at 855-743-3427, or check us out online at SuperATV.com. Thanks for watching and we’ll catch you next time.

RELATED CONTENT: installation262 machine protection22 nerf bars8 Polaris RZR PRO XP26
Share
0

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *



Related

  • How to Install a Heavy-Duty Carrier Bearing on a Polaris Ranger Crew

    How-To | 11 MIN READ
  • How to Install a 4500 Lb. Black Ops Winch on a Polaris RZR

    How-To | 12 MIN READ
  • How to Install a Winch-Ready Bumper and Black Ops Winch on a Polaris Ranger XP 1000

    How-To | 12 MIN READ
  • How to Install a High Gear Kit and Clutch Kit on a Polaris RZR XP Turbo

    How-To | 18 MIN READ
  • How to Install a 6" GDP Portal Gear Lift on a Can-Am Defender

    How-To | 17 MIN READ
  • How to Service, Rebuild, and Maintain 6" GDP Portals

    How-To | 8 MIN READ
  • How to Install a Heavy-Duty Rhino Driveline Prop Shaft on a Polaris RZR XP Turbo

    How-To | 8 MIN READ
  • How to Install a 4" GDP Portal Gear Lift on a Polaris RZR PRO XP

    How-To | 13 MIN READ
  • How to Install a Heavy-Duty Carrier Bearing on a Polaris General 1000

    How-To | 7 MIN READ
Copyright © 2021 SuperATV. All rights reserved.
SHOP NOW